View DCC-SC01HD32_2795728.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. color hd 720p board camera DCC-SC01HD32 product specification & operational manual cis corporation en g lish www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 1 table of contents page 1. scope of application 2 2. handling precautions 2 3. product outline 3 4. bundled items 3 4.1. standardbundled items 3 4.2. optional items 3 5. specifications 4 5.1. general specifications 4 5.2. camera input/output signals 5 6. part names and functions 6 7. external connector pin assignment 7 7.1. power input and signal outp ut connectors (harness 2050) 7 7.2. osd switch connectors (har ness sc01osd) optional connectors 8 7.3. remote control cable connectors 8 8. camera operating instructions 9 8.1. switch operation without osd menu 9 8.2. pc operation via rs232c 9 8.3. switch operation with osd menu 9 9. factory settings (underlined and bold letters show the factory settings) 15 10. dimensions 16 11. cases for indemnity (limited warranty) 17 12. cmos pixel defect 17 13. product support 17 www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 2 1. scope of application this is to describe DCC-SC01HD32, anlog color hd (720p) board camera assembly. all specifications contained herein are subject to change without prior notice. reproduction in whole or in part is prohibited. 2. handling precautions the camera assembly must not be used for any nuc lear equipments or aerospace equipments with which mechanical failure or malfunction could result in serious bodily injury or loss of human life. our warranty does not apply to damages or defects caused by irregular and/or abnormal use of the product. please observe all warnings and cautions stated below. our warranty does not apply to damages or malfunctions caused by neglecting these precautions. z do not directly touch the board camera while camera is in operation. the board camera can be very hot and you may burn yourself. z do not apply excessive voltage. (use only the sp ecified voltage.) unstable or improper power supply voltage may cause damages or malfunction of the camera. z do not directly touch the optical surface. cmos image sensor is fragile. z do not use or store the camera assembly in th e dusty or humid places. z do not apply excessive force or static electr icity that could damage the camera assembly. z in some cases, hunting may occur when using el ectric iris, depending on the object to shoot. z in some cases, color may change under fl uorescent lamp when using electiric iris. z do not shoot direct images that are extremely br ight (e.g., light source, sun, etc). when the camera is not in use, please put the protection cap on. z follow the instructions in chapter 7, ?external connector pin assignment? for connecting the camera. improper connection may cause damages not only to the camera but also to the connected devices. in case of abnormal operation, contact the distributor from whom you purchased the product. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 3 3. product outline DCC-SC01HD32 is a hd (720p) output, color board camera assembly utilizing 1/3 type cmos image sensor. with our own image processing technologies, electrical zoom, long time exposure function, osd functions, and others are incorporated into the camera. 32x32 42x42 (2 boards) in size should best match for embedded systems. hd 720p/60, 720p/59.94 720p/50 analog component (y/pb/pr) and rgb outout available. key features long time exposure shutter function enables to capture clear images even under low illumination. on screen (osd) function enables to set camera settings by menu. (osd operational switch needed). camera settings can be set with rs 232c via pc. (dedicated remote control unit needed). 4. bundled items 4.1. standardbundled items board camera harness 2050: for power supply and video sign al output. (10pins connector, 10 cores) camera attachment screws (4pcs) protection cap or seal (with optional lens, prot ection cap will be inclosed. without optional lens, protection seal will be inclosed.) 4.2. optional items dedicated lens harness sc01osd: for osd switch connection. (10pins connector, 5 cores) re-300a: remote control cable (between camera and pc) www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 4 5. specifications 5.1. general specifications (1) pick up device device type 1/3 type cmos sony imx035lqr-c effective pixel numbers 1329(h) 1049(v) unit cell size 3.63 m(h) 3.63 m(v) chip size 7.64mm(h) 7.64mm(v) (2) resolutions 1280(h) 720(v) (3) aspect ratio 16 : 9 (4) video output frequency 60fps horizontal frequency 45 khz vertical frequency 60 hz 59.94fps horizontal frequency 44.95 khz vertical frequency 59.94 hz 50fps horizontal frequency 37.50 khz vertical frequency 50 hz (5) sync. system internal sync (6) video output standard analog co mponent output : y/pb/pr 1vp-p (3 values, sync signals) 75 ? terminal rgb output : rgb 1vp-p (without sync ) 75 ? terminal hd, vd t tl level (over 2.1 v 1k ? terminal) (7) horizontal resolution 600tv lines (contour correction sharp) (8) sensitivity f4.0 2000lx (9) minimum illumination 60fps,59.94fps : f2.5 6.0lx (with dedicated board camera lens) f1.4 3.0lx (with f1.4 lens) 50fps : f2.5 5.0lx (with dedicated board camera lens) f1.4 2.5lx (with f1.4 lens) conditions : video 50%, agc 36db, electrical shutter off (10) dust or stains in optical systems no dust or stain shall be detected on the testin g screen with dedicated lens installed, or with setting the camera aperture at f16 if there is no lens. (11) power requirements dc+9 +15v (12) power consumption 2.0w (max. 2.4 w) at dc+12v in (13) dimension refer to overall dimension drawing. (14) mass approx. 45g (including optional dedicated lens). (15) lens mount dedicated board camera lens mouont. refer to overall dimension drawing. (16) gain setting agc (max gain : +18db, +24db, +30db, +36db), agc off(0db) manual : 0db 36db (17) shutter speed variable range off : 1/60(60fps, 59.94fps),1/50(50fps) fl : 1/100(60fps, 59.94fps), 1/120(50fps) manual : 1/10k, 1/4k, 1/2k, 1/1k, 1/500, 1/250, 1/120, 1/100, 1/60, 1/50, 1/30, 1/25, 1/15, 1/8, 1/4, 1/2, 1s, 2s, 4s, 8s auto : 1/10ks 8s (upper or lower limit can be set.) (18) white balance adjustment range atw1 : 2200 9000k, atw2 : 3200 6500k preset:3200k, 4800k, 6500k, manual: 2200 9000k (19) electrical zoom 1 4 pan, tilt (20) auto iris signals responses are ad j ustable. usable with electrical shutter (with priority to electrical shutter). www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 5 (21) back li g ht devided into 49 screens (7x7), and each screen can be individually masked. (masked part shall be ignored.) the same settings are applicable to atw. (22) character display character display: alphanumeeric characters and symbols (max 24 letters) display position: t he upper left portion of the screen (fixed) characters can be edited by osd. (23) contour correction sharp/std./soft selectable. (24) chromaticness adjustment chromaticness is ad j ustable. 255(typ.) 0(b/w) (25) gamma compensation gamma is ad j ustable. =0.45 1.0 data (127 0) (26) pixel defect (white spot) correction off/on (initial settin g ) / on (user settin g ) maximum correction value: 63 values (dependin g on conditions.) maximum correction value and detecion start level can be set. when correction is started after blockin g li g ht, lon g time exposure and a gc is set automatically to start. (27) remote control operation operatable via rs232c. 9600bps(typ), with no parity, stop pit: 1bit communication speed selection : 2400, 4800, 9600, 19200 bps (28) safety/quality standards ul: conform to ul standard includin g materials and others. ce: emmission: en55022:2006(class b) immunity: en55024:1998/a1:2001/a2:2003 rohs: conform to rohs (29) operational environment specifications guaranteed 0 +40 humidity: 20 80%rh with no condensation operation guaranteed -5 +45 humidity: 20 80%rh with no condensation (30) storage environment temperature : -25 +60 humidity: 20 80%rh with no condensation. 5.2. camera input/output signals video signals white clip level: 760mv 10% sync level: 300mv 10% (3values sync signals) www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 6 2 3 4 5 1 6 7 cn4 cn6 cn5 cn2 cn3 (no mount) (no mount) 6. part names and functions power input and video output with the bundled harness, poiwer input and vide o output signals are connected to a monitor. please refer to chapter 7, ?external connector pin assignment?. osd operational switch connector with the optional harness, osd operational switch is connected. please refer to chapter 7, ?external connector pin assignment?. remote control connector optional remote control cable (re-300a) is connected. with connecting the remote control cable (re-300a) to a pc, serial communication via rs-232c is valid. please refer to the other materials for the communication details. (to be prepared) dedicated board camera lens lenses are optional. camera mounting holes with bundled attachment screws, mount the camera. extended connectors (not implemented. can be implemented on request.) dc iris connectors (not implemented. can be implemented on request.) www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 7 pb/b_out pr/r_out hd out gnd iris_sig dc+12vin vd out y/g_out 1 2 3 4 5 6 7 8 9 10 51021-1000 to monitor y pr pb dc+12v gnd +12v gnd iris out to video iris lens power in n.c. n.c. gnd gnd (component terminal) pb/b_out pr/r_out hd out gnd iris_sig dc+12vin vd out y/g_out 1 2 3 4 5 6 7 8 9 10 51021-1000 to monitor dc+12v gnd +12v gnd iris out to video iris lens power in gnd gnd 1 5 610 11 15 234 7 89 12 13 14 hd15pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 red green blue n.c. gnd gnd ( red ) gnd ( green ) gnd ( blue ) n.c. gnd n.c. sda hsync vsync scl n.c. n.c. n.c. n.c. n.c. (vga terminal) 7. external connector pin assignment 7.1. power input and signal output connectors (harness 2050) connectors of camera side connectors of bundled harness side 53398-1090 (molex) 51021-1000 (molex) cn4 signals component output rgb output 1 pb/b out pb output (3values sync) blue output (without sync) 2 pr /r out pr output (3values sync) red output (without sync) 3 iris out video iris signals 4 hd out hd output 5 gnd gnd (for video signals) 6 vd out vd output 7 gnd gnd (for video signals) 8 y/g out y output (3values sync) green output (without sync) 9 gnd gnd (power) 10 power power input (dc+12v) connection for component y/pb/pr output connection for rgb output www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 8 1 2 3 4 5 6 7 8 9 10 shr-10v-s-r up back enter down gnd sw_back sw_up sw_enter sw_down 7.2. osd switch connectors (harness sc01osd) optional connectors connectors of camera side connectors of optional harness side bm10b-srss (nichiatsu) shr-10v-s-b (nichiatsu) cn6 signals 1 n.a. (open) 2 n.a. (open) 3 n.a. (open) 4 n.a. (open) 5 n.a. (open) 6 gnd gnd for switch connection 7 sw_back switch connecting terminal (back) 8 sw_up switch connecting terminal (up) 9 sw_enter switch connecting terminal (enter) 10 sw_down switch connecting terminal (down) 7.3. remote control cable connectors connectors of camera side connectors of remote control cable side 53398-0271 (molex) 51021-0200 (molex) cn6 signals 1 gnd remote control gnd 2 remote remote control signals (input/output) www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 9 8. camera operating instructions there are 3 different operating methods, operatin g with osd menu, operating without osd menu, and operating via pc with dedicated remote control cable connected to the remote control terminals. depending on its operating methods, selectable came ra settings are different. please refer to the selectable settings by each operational method as below. 8.1. switch operation without osd menu operational functions ezoom, pan, tilt, and video format selection ezoom operation ezoom can be operated with [up] key and [down] key. with [down] key, it goes to tele side, and with [up] key, it goes to wide side. except when ezoom is x1.00, it goes to ezoom pan tilt ezoom everytime when [back] key is pushed. pan and tilt values can be set as well. * when ezoom is x1.00, pan and tilt will automatically go back to the center of the image. display format selection video format can be changed as follows, pushing [enter] key while pushing [back] key. 720p/60 y/pbpr 720p/59.94 y/pbpr 720p/50 y/pb/pr 720p/60 rgb 720p/59.94 rgb 720p/50 rgb 720p/60 y/pb/pr * the selected settings with operations explaine d the above can not be saved as they are. to save those settings, exit save shall be done by osd displayed operation. * initial setting is 720p/59.94 y/pb/pr. 8.2. pc operation via rs232c camera can be controlled via a pc using camera co ntrol software, with dedicated remote control cable (re-300a) connected to the remote control terminal. 8.3. switch operation with osd menu [enter] key: to enter into the menu with pushing this button for long. in the menu, this button works to go to the next menu, and works as [ ] key. [back] key: in the menu, this button works to go back to the prior menu, and works as [ ] key. [up] key: to select items in the menu. when operating volume type menu, this button makes the value to direction. [down] key: to select items in the menu. when operating volume type menu, this button makes the value to direction. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 10 main menu items select next menu explanation gain off set agc off to make gain 0db. agc> max gain set agc on. [enter] to go to the next menu to enable to set the maximum gain. manual> manual gain set gain manually. [enter] to go to the next menu to enable to set the manual value. shutter off set the electronic shutter off. the same shutter speed set as frame rate will be set. fl set to be flickerless. when the set frame rate is 60fps, and 59.94fps, 1/100s shutter speed will be set, while the set frame rate is 50fps, 1/120s shutter speed will be set. aes> aes setting operate auto electronic shutter. [enter] to go to the next menu to enable low shutt, lim (limitation of electronic high sensitivity), and high shutt lim (limitation of high speed electronic shutter). manual> manual shutter set the electronic shutter manually. [enter] to go to the next menu to enable to set the manual value. white_bal atw> atw setting operate auto white balance. [enter] to go to the next menu to enable to set tracking range, tracking speed, and off set of convergent point. 3200k fix white balance to 3200k. 4800k fix white balance to 4800k. 6500k fix white balance to 6500k. mwb> manual white bal set white balance manually. [enter] to go to the next menu to enable to set the manual value. aeset level> ae level [enter] to go to the next menu to enable to set the blightness of auto exposure. respons> ae respons [enter] to go to the next menu to enable to set the operational speeds of agc, aes, and auto iris. volume adjustment of video iris can be checked as well. blc> blc setting [enter] to go to the next menu to enable to set back light setting. option picture> picture [enter] to go to the next menu to enable to set the image sharpness, gamma compensation, saturation, and defective pixel correction of the image sensor. ezoom> ezoom [enter] to go to the next menu to enable to set electronic shutter. display> display [enter] to go to the next menu to enable to set the display settings of title indication and electronic zoom magnifications. remote> remote setting [enter] to go to the next menu to enable to set the serial communication speed. exit save> end save the data set with osd, and terminate the menu. cansel> end restore the data set with osd, and terminate the menu. default> end restore the data to the initial settings, and terminate the menu. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 11 max gain items select next menu explanation max gain 18db set the maximum gain of agc. 24db 30db 36db manual gain items select next menu explanation manual gain 0db-36db set the manual gain. aes setting items select next menu explanation low shutt.lim 8s,4s,2s,1s, 1/2,1/4,1/8, 1/15,1/25, 1/30,1/50, 1/60,1/100, 1/120,1/250, 1/500,1/1k, 1/2k,1/4k, 1/10k limit the low speed limitation of electronic shutter auto. higher speed than high shutt.lim. can?t be set. high shutt.lim 8s,4s,2s,1s, 1/2,1/4,1/8, 1/15,1/25, 1/30,1/50, 1/60,1/100, 1/120,1/250, 1/500,1/1k, 1/2k,1/4k, 1/10k limit the high speed limitation of electronic shutter auto. lower speed than low shutt.lim. can?t be set. manual shutter items select next menu explanation shutter speed 8s,4s,2s,1s, 1/2,1/4,1/8, 1/15,1/25, 1/30,1/50, 1/60,1/100, 1/120,1/250, 1/500,1/1k, 1/2k,1/4k, 1/10k set the shutter speed manually. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 12 atw setting items select next menu explanation atw range atw1 set the atw range to 2200 9000k. atw2 set the atw range to 3200 6500k. atw res slow set the speed of atw. mid. fast r offset 0-255 adjust r offs et value of atw white standard. b offset 0-255 adjust b offs et value of atw white standard. manual white bal. items select next menu explanation one push end one push to set the manual white balance value automatically. [d]: to go to end->cal to start detection. with completion, it goes to cal->end and its results are reflected in red gain and in blue gain. r/b offset of atw setting is to be reflected. cal. red gain 0-255 gain adjustment of red. blue gain 0-255 gain adjustment of blue. ae level items select next menu explanation ae level 0-127 set the ae level. operate agc, aes, and auto iris settings. ae respons items select next menu explanation agc res. 0-255 set the response speed of agc. the bigger the value goes, the slower the speed will be. aes res. 0-255 set the response speed of aes. the bigger the value goes, the slower the speed will be. iris res. 0-255 set the response speed of auto iris. the bigger the value goes, the slower the speed will be. hunting may occur if the speed is too fast. iris level 0-127 set video iris typed auto iris lens. please refer to the usage method of auto iris lens. blc setting items select next menu explanation blc setting off off back light. (full photometry) on(33) on back light. (center 33) on(user) > blc window set on back light. with the next menu, window settings can be done. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 13 picture items select next menu explanation sharpness soft set the sharpness. std. sharp gamma 0-127 set gamma. (data 127: P 0.45) chroma 0-255 set chromaticness. data 0: b/w blemish comp. off off pixel defect correction of image sensor (white spot). user> blemish comp. on pixel defect correction of image sensor (white spot) by user setting. [enter] to go to the next menu to enable to correct blemish by user settings. fact. on pixel defect correction of image sensor (white spot) by factory setting. ezoom items select next menu explanation ezoom 1-4 set magnification of electronic zoom. pan 0-255 when magnification ratio is more than x1, video output range can be horizontally shifted. when magnification ratio is x1, pan value becomes 128 and the video output range will return to the center. tilt 0-255 when magnification ratio is more than x1, video output range can be vertically shifted. when magnification ratio is x1, pan value becomes 128 and the video output range will return to the center. display items select next menu explanation title off off the display of title indication. char> cam title edit on the display of the title indication. alphanumeeric characters and symbols can be displayed. [enter] to go to the next menu to enable to edit. mode off off the video format indication and electronic zoom indication when the menu is undispalyed. on on the video format indication and electronic zoom indication when the menu is undispalyed. when video format is changed, it is indicated and disappears automatically after approx. 10 seconds. when pan, tilt, and ezoom are changed, it is indicated and disappears automatically after approx. 5 seconds. remote setting items select next menu explanation bit rate 19200bps set the speed of serial communication. 9600bps 4800bps 2400bps www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 14 blc window set items select next menu explanation 7x7(49) window mask set/clr window0 window48 set mask on/off for back light. the masked area (whiteout part) will not be reflected by auto exposure. [d]: to mask on and goes to the next area. [u]: to mask off and goes to the next area. blemish comp. items select next menu explanation user comp. disp. indicate the corrected are by pixel defect correction (white spot) with blinking. start start detection of pixel defect area (white spot) with sheilding and blacking-out the entire lens. with successfully completed, transmit to disp and display the area to be corrected with blinking. if not successfully completed, transmit to error. error if not shielded or max q?ty is too low, error might occur. in such case, shiled completely and increase the max q?ty to restart. start level 16-127 set the beginning level to start detection. the level will go higher gradually from this level. max. qty 4-63 set the maximum q?ty to detect. the q?ty to be detected shall be less than this q?ty. if there are too many areas to be corrected, reduce this q?ty. cam title edit items select next menu explanation character selection abcdefgh ijklmnop qrstuvw xyz abcdefghijk lmnopqrstu vwxyz-.,()0 123456789 [u], [d] to select characters, and [enter] to shift the character position to edit to the right. usage method of auto iris lens this camera outputs signals for auto iris so that video iris lenses can be connected. here, we would like to explain how to adjust variable resister installed in the video iris lenses. please refer to the section 7, external connector pin assignment, for connection. first of all, set gain off and shutter off, then set aeset >ae respons with osd menu. try to shoot the area as blight as possible, set the alc volume to av side, and then, adjust the level volume of lens-side, trying to position the icursor of iris level to be center. after adjusting, restore gain and shutter settings to be used. when adjustin g blightness, please do not use lens-side volume. adjsut the blightness with ae level after the explained adjustment is completed. if lens-side volume is forced to use to adjust blightness, agc and aes would not work properly in conjunction with the other. www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 15 9. factory settings (underlined and bold letters show the factory settings) osd settings main gain off agc> max gain 36db manual> manual gain 0db shutter off fl aes> low shutt.lim. 1/8 high shutt.lim. 1/10k manual> shutter speed 1/250 white_bal atw> atw range atw1 atw res mid. r offset 128 b offset 128 3200k 4800k 6500k mwb> one push end red gain 128 blue gain 128 aeset level> ae level 64 respons> agc res. 32 aes res. 32 iris res. 32 iris level - blc> blc setting off on(3x3) on(user)> center(1) option picture> sharpness std. gamma 127 chroma 192 blemish comp. off user> user comp. disp. start level 16 max. qty 63 fact. ezoom> ezoom x1.000 pan 128 tilt 128 display> title off char> dcc-sc01hd 32 mode off on remote> bit rate 19200bps 9600bps 4800bps 2400bps exit save> cansel> default> www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 16 4-f 2.2 hole 4-r1 19 31 42 0.3 38 0.15 42 0.3 38 0.15 32 32 10.5 (19.2) 8.7 2 (mounting surface to imaging surface) cn6 cn4 cn5 12 2.55 999-540-00-00 (unit:mm) m141.0 10. dimensions www.datasheet.co.kr datasheet pdf - http://www..net/
DCC-SC01HD32 rev.900-717-30-00 ?2010 cis corporation. all rights reserved. 17 11. cases for indemnity (limited warranty) we shall be exempted from taking responsibility an d held harmless for damage or losses incurred by the user in the following cases. z in case damage or losses are caused by fire, earthquake, or other acts of god, acts by third party, deliberate or accidental misuse by the user , or use under extreme operating conditions. z in case indirect, additional, consequential damage s (loss of business interests, suspension of business activities) are incurred as result of malfunction or non-function of the equipment, we shall be exempted from responsibility for such damages. z in case damage or losses are caused by failure to observe the information contained in the instructions in this product specification & operation manual. z in case damage or losses are caused by use co ntrary to the instructions in this product specification & operation manual. z in case damage or losses are caused by malfunct ion or other problems resulting from use of equipment or software that is not specified. z in case damage or losses are caused by repair or modification conducted by the customer or any unauthorized third party (such as an unauthorized service representative). z expenses we bear on this prod uct shall be limited to the individual price of the product. 12. cmos pixel defect cis compensates the noticeable cmos pixel defects (white spot) found at the shipping inspection prior to our shipment. on very rare occasions, however, cmos pixel defects might be noted with time of usage of the products. the cause of the cmos pixel defects is the charac teristic phenomenon of cmos itself and cis is exempted from taking any respon sibilities for them. pixel defects (white spot) compensation cis performs is not to guarantee its effects to whole white spot. cmos pixel defects (white spot) may be seen when gain is increased by agc or when slow shutter is used, however, this shall not be considered as an inferiror product. 13. product support when defects or malfunction of our products occur, and if you would like us to investigate on the cause and repair, please contact your distributors you purchased from to consult and coordinate. camera control sample software (rs232c) is down loadable via our web but we shall be exempted from taking responsibility and held harmless for damage or malfunction of your hardware and software caused by using this control software. the purpos e of this control software is for you to check operation and evaluate our products. please be noted that cis does not customize the program nor provide source code. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of DCC-SC01HD32

	To Download DCC-SC01HD32 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .